Taylor 8757 Скачать руководство пользователя страница 47

Страница: 47 / 58

Section 8

8-1

Models 8752, 8756, and 8757

Troubleshooting Guide

Table 8-1

Problem

Probable Cause

Remedy

Page

Ref.

1. No product is being

dispensed.

a. Low on mix. The MIX OUT light is

on.

a. Add mix to the mix tank and press the

AUTO button.

5-1

b. The power switch is in the OFF

position.

b. Place the power switch in the ON

position and press the AUTO button.

- - -

c. The beater motor is out on reset.

c. Reset the freezer.

5-1

d. The beater assembly is rotating

counterclockwise.

d. Contact service technician to correct

rotation to clockwise.

- - -

e. Insufficient mix in the freezing

cylinder.

e. Go to problem 2.

- - -

f. Restriction in the door spout.

f. Remove the draw handle and raise

the draw valve all the way up to
remove restriction. Never put objects
or fingers in door spout.

- - -

g. Machine is unplugged.

g. Plug machine into the wall receptacle.

- - -

h. Circuit breaker is off or the fuse is

blown.

h. Turn the breaker on or replace the

fuse.

- - -

i. The mix probe was not installed

properly or was damaged.

i. Check the mix probe installation.

6-12

Содержание 8757



























































Результаты поиска

Содержание 8757

Отзывы:

Похожие инструкции для 8757

Бренды по названию

Популярные бренды

Taylor 8757, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 8757

Отзывы:

Похожие инструкции для 8757

Бренды по названию

Популярные бренды