Taylor 8757 Скачать руководство пользователя страница 44

Страница: 44 / 58

6-16

OPERATING PROCEDURES

Models 8752, 8756, and 8757

Operating Procedures

Check Topping Pump Temperature

and Volume - Model 8757

To check the topping pump temperature and volume on
Model 8757 the following items will be needed:
•

Digital thermometer with needle probe

•

Calibrating cup

•

Flatblade screwdriver

•

Sanitizer (examples: Stera Sheen

or Kay-5

)

Note:

This procedure should be performed on a

morning after the pumps were disassembled and
cleaned, on a monthly basis.

1. Dispense one serving of topping into a sundae cup.

2. Insert the sanitized needle probe into the topping. Let

the probe stabilize for 20 seconds.

Note:

Topping temperature should be between

115°F and 125°F (46°C and 52°C) and must be this
temperature before pump calibration can begin.
Water bath temperature should be between 135°F
and 145°F (57°C and 63°C).

3. If the temperature is too cold or too warm, it can be

adjusted by the temperature control located inside
the machine on the back of the topping compartment.

4. Using the flatblade screwdriver, loosen and remove

the screws from the lower right panel. Locate the
adjustment screws, one for each water bath.

5. Using a flatblade screwdriver, turn the adjustment

screw

clockwise

increase

and

counterclockwise

decrease

the water bath

temperature. Adjust in small increments.

6. Allow 10 minutes for the temperature to stabilize in

the water bath.

7. Check the temperature again in the water bath.

8. Place the topping pump back into the container.

9. Repeat these steps for the other topping. Install the

lower right panel, if applicable, and install the screws.

10. Hold the small chamber of the calibrating cup under

the dispensing nozzle.

11. Push the dispensing lever down for one full stroke.

The topping should be directed to the bottom of the
calibrating cup.

Do Not

allow the topping to fall on

the sides of the cup.

Note:

The amount of dispensed topping should be



1 fl. oz. (29.6 ml).

12. If the dispensed amount is correct, proceed to

step 13. If the amount of dispensed topping is not
correct, consult the Troubleshooting Section of your
machine manual.

13. Repeat steps 10 through 12 for the other topping

pump, then proceed with step 14.

14. Topping pump temperature and volume check is

complete.

Содержание 8757



























































Результаты поиска

Содержание 8757

Отзывы:

Похожие инструкции для 8757

Бренды по названию

Популярные бренды

Taylor 8757, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 8757

Отзывы:

Похожие инструкции для 8757

Бренды по названию

Популярные бренды