background image

Section 11

11-1 

Model 104

Limited Warranty on Parts 

 11

Limited Warranty on Parts

TAYLOR COMPANY LIMITED WARRANTY ON GENUINE TAYLOR  PARTS 

Taylor Company is pleased to provide this limited warranty on new Taylor genuine replacement components and parts 
available from Taylor to the market generally (the “Parts”) to the original purchaser only.

LIMITED WARRANTY

Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service as 
follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails due to 
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency, will 
provide a new or remanufactured Part, at Taylor’s option, to replace the failed defective Part at no charge for the Part. 
Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for a Part failure. 
This limited warranty is subject to all provisions, conditions, limitations, and exclusions listed below and on the reverse 
(if any) of this document.

Table 11-1

LIMITED WARRANTY CONDITIONS

1. If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required at time 

of service.

2. This limited warranty is valid only if the Part is installed and all required service work in connection with the Part is 

performed by an authorized Taylor distributor or service agency.

3. The limited warranty applies only to Parts remaining in use by their original owner at their original installation 

location in the unit of original installation.

4. Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in the 

Taylor Operator’s Manual.

5. Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.

6. This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate Taylor 

Limited Warranty on freezer or grill equipment.

7. The use of any refrigerant other than that specified for the unit in which the Part is installed will void this limited 

warranty.

Parts Warranty Class Code Or Part

Limited Warranty Period

Class 103 Parts

¹

Three (3) Months

Class 212 Parts

²

Twelve (12) Months

Class 512 Parts

Twelve (12) Months

Class 000 Parts

No Warranty

1, 2

 Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1 

(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor freezer 

equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.

Содержание 104









































Отзывы: