Taylor-Dunn RE-380-36 Скачать руководство пользователя страница 96

Страница: 96 / 150

Batteries

Page 96

RE-380-36 & RE-380-48

MR-380-05

HARDWARE TORQUE

If hardware is not listed here, refer to standard torque

values in the appendix.

Description

Inch Pounds

Newton Meters

Battery terminal, Trojan bolt

95-105

11-12

Battery terminal, Trojan stud

95-105

11-12

Battery terminal, T/D bolt

168

Battery removal, 48 Volt System

Batteries for the 48 volt system are packed into a small

area and requires a specific procedure to get them out of

the vehicle. Refer to Individual Batteries section for actual

battery removal instructions for an individual battery.

The illustration to the right shows the left bank of a typical

battery installation in a vehicle with the 48 volt system

with the cables removed. Some components have been

omitted for clarity

Note: The charger may have to be removed to

provide clearance.

1: Remove all of the battery cables from the

batteries.

2: Remove the battery hold downs.

3: Lift the rear battery at an angle as shown.

4: Lift the front battery at an angle as shown and

remove the battery from the vehicle.

5: The remaining batteries can now be removed.

6: Repeat the same procedure for the four batteries

on the right side.

Содержание RE-380-36























































































































































Результаты поиска

Содержание RE-380-36

Отзывы:

Taylor-Dunn RE-380-36, Инструкция по обслуживанию и замене запасных частей, Страница: 96 / 150

Результаты поиска

Содержание RE-380-36

Отзывы: