Taylor-Dunn RE-380-36 Скачать руководство пользователя страница 62

Страница: 62 / 150

Steering

Page 62

RE-380-36 & RE-380-48

MR-380-05

REPLACE STEERING WHEEL

Note: The steering wheel is on a tapered shaft and may be damaged when it is removed.

1: If equipped with a horn switch in the steering wheel,

remove the switch and disconnect the wires from the

switch.

2: Remove the steering wheel nut.

3: Using a steering wheel puller, remove the steering wheel.

4: Position the front wheels in the straight ahead position.

5: Lightly grease the steering wheel splines and install the

replacement steering wheel orientated as shown in the

illustration.

6: Tighten the steering wheel nut to torque listed in the

Hardware Torque table at the end of this section.

7: Reinstall the horn switch (if equipped).

8: Reconnect the main positive and negative cables at the

batteries.

9: Remove the blocks from behind the wheels.

10: Release the parking brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание RE-380-36























































































































































Результаты поиска

Содержание RE-380-36

Отзывы:

Taylor-Dunn RE-380-36, Инструкция по обслуживанию и замене запасных частей, Страница: 62 / 150

Результаты поиска

Содержание RE-380-36

Отзывы: