manualshive.com logo in svg

Taylor-Dunn RE-380-36, Инструкция по обслуживанию и замене запасных частей, Страница: 60 / 150

Поделиться
Скачать
Taylor-Dunn RE-380-36 Скачать руководство пользователя страница 60

Steering

Page  60

RE-380-36 & RE-380-48

MR-380-05

REPLACE BALL JOINT

1:  Raise the front of the vehicle and support with jack stands.

2:  Loosen the ball joint clamp on the steering sleeve.

3:  Remove the cotter pin and ball joint nut.

4:  Using a pickle fork, remove the ball joint from the steering arm.

5:  Remove the ball joint from the steering sleeve.

Note: Count the number of turns needed to remove the ball joint.

6:  Install the new ball joint into the steering sleeve. Screw it into the sleeve 

the same number of turns counted in the previous step. Do not tighten the 

ball joint clamp at this time.

7:  Install the ball joint into the steering arm. Tighten the ball joint nut per 

torque listed in the Hardware Torque table at the end of this section and 

install a new cotter pin.

8:  Realign the front wheels. Refer to the Front Axle section for information 

regarding realignment of the front wheels.

9:  Lower the vehicle.

10: Reconnect the main positive and negative cables at the batteries.

11:  Remove the blocks from behind the wheels.

12: Release the park brake and test drive.

This section is one section of a complete service 

manual. Before starting any procedure, read all 

warnings and instructions that are located in the 

Service Guidelines chapter.

WARNING

REPLACE ROD END

1:  Raise the front of the vehicle and support with jack stands.

2:  Loosen the rod end clamp or jam nut on the steering sleeve.

3:  Remove the nut or bolt holding the rod end onto the steering arm.

4:  Remove the ball joint from the steering sleeve.

5:  Install the new rod end into the steering sleeve. Screw it into the sleeve 

the same number of turns counted in the previous step. Do not tighten 

the rod end clamp or jam nut at this time.

6:  Install the rod end into the steering arm. Tighten the ball joint nut per 

torque listed in the Hardware Torque table at the end of this section.

7:  Realign the front wheels. Refer to the Front Axle section for information 

regarding realignment of the front wheels.

8:  Lower the vehicle.

9:  Reconnect the main positive and negative cables at the batteries.

10: Remove the blocks from behind the wheels.

11:  Release the park brake and test drive.

This section is one section of a complete service 

manual. Before starting any procedure, read all 

warnings and instructions that are located in the 

Service Guidelines chapter.

WARNING

Содержание RE-380-36























































































































































Отзывы:

Нет отзывов