Taylor-Dunn E0-455-24 Скачать руководство пользователя страница 55

Страница: 55 / 134

Steering

Page 55

ME-455-04

E-455

REPLACE THE FRONT FORK

1: Remove the front axle. Refer to section Front

Axle Removal and Installation in Front Axle

Service for information regarding removing the

front axle.

2: Remove the ball joint from the fork.

3: While supporting the front fork so that it cannot

fall out of the vehicle, remove the fork spindle nut

and remove the fork from the vehicle.

4: Thoroughly clean all parts and install in reverse

order.

•

Tighten the fork spindle nut to remove all play

in the fork bearings and then an additional 1/4

turn.

•

Refer to section Front Axle Removal and

Installation in Front Axle Service for information

regarding installing the front axle.

•

If the fork was replaced with a new fork the

front end should be realigned. Refer to section

Front End Alignment for information regarding

aligning the front end.

5: Test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

REPLACE STEERING WHEEL

Note: The steering wheel is on a tapered shaft and may

be damaged when it is removed.

1: If equipped with a horn switch in the steering wheel,

remove the switch and disconnect the wires from the

switch.

2: Remove the steering wheel nut.

3: Using a steering wheel puller, remove the steering

wheel.

4: Position the front wheels in the straight ahead

position.

5: Lightly grease the steering wheel splines and install

the replacement steering wheel orientated as shown

in the illustration.

6: Tighten the steering wheel nut to torque listed in the

Hardware Torque table at the end of this section.

7: Test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание E0-455-24







































































































































Результаты поиска

Содержание E0-455-24

Отзывы:

Похожие инструкции для E0-455-24

Бренды по названию

Популярные бренды

Taylor-Dunn E0-455-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание E0-455-24

Отзывы:

Похожие инструкции для E0-455-24

Бренды по названию

Популярные бренды