Taylor-Dunn E0-455-24 Скачать руководство пользователя страница 30

Страница: 30 / 134

Front Axle

Page 30

E-455

ME-455-04

INSPECT FRONT WHEEL
BEARINGS

1: Raise the front of the vehicle and support with

jack stands.

2: Grab the top and bottom of the tire/wheel

assembly. Feel for any movement or play while

pulling and pushing on the top and bottom of the

tire. Any movement or play is indication of loose

wheel bearings.

3: Spin the front wheel(s) by hand. The wheel

should stop spinning in no more than

2-revolutions. A wheel that continues to spin

freely is an indication of a loose wheel bearing.

Note: Refer to the Adjust Front Wheel Bearings

section for detailed information regarding the

proper adjustment of the wheel bearings.

4: Spin the wheel(s) and listen for any grinding

noise. Any noise may be an indication of worn or

damaged wheel bearings.

Note: Refer to the Replace Front Wheel Bearings

section for information regarding the

replacement of the wheel bearings.

5: Lower the vehicle.

6: Reconnect the batteries.

7: Remove the blocks from behind the wheels.

8: Release the park brake and test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

ADJUST FRONT WHEEL BEARINGS

•

The bearings must be lubricated before performing

this procedure.

1: Raise the front wheel(s) off of the ground and

support with jack stands.

While rotating the wheel

, tighten the front axle

nut until the wheel is difficult to rotate.

3: Continue to rotate the wheel for 5 compete

revolutions.

4: Attach a rope to the tire and wrap around the tire

with 1 foot remaining hanging in the air.

5: Tie a weight (see table and illustration below) to

the end of the rope.

6: Slowly loosen the axle nut until the hanging

weight rotates the wheel.

7: Remove the rope and weight.

8: Spin the wheel and listen for any grinding noise.

Any grinding noise may be an indication of worn

or damaged wheel bearings.

Note: Refer to the Replace Front Wheel Bearings

section for information regarding the

replacement of the wheel bearings.

9: Lower the vehicle.

10: Reconnect the main positive and negative cables

at the batteries.

11: Remove the blocks from behind the wheels.

12: Release the park brake and test drive the vehicle.

Note: Vehicles with front fork suspension may

require a tighter used bearing adjustment.

When test driving the vehicle watch for any

shimmy in the steering. If any shimmy is

noticed first inspect the fork collar bearing

adjustment. If OK then tighten the preload

in small increments until it stops.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Tire Size

Weight NEW

(pounds / kg)

Weight USED

(pounds / kg)

4.80 x 8

2.15 / 0.975

1.00 / 0.454

5.70 x 8

1.99 / 0.902

0.93 / 0.422

4.00 x 8

2.15 / 0.975

1.01 / 0.485

500 x 8

1.99 / 0.902

0.93 / 0.422

8.50 x 8

2.02 / 0.916

0.94 / 0.426

8 x 2.50

4.23 / 1.919

1.97 / 0.894

10 x 3.5

3.38 / 1.533

1.56 / 0.708

NEW: Weight = 16.931 / Radius
USED: Weight = 7.875 / Radius

Содержание E0-455-24







































































































































Результаты поиска

Содержание E0-455-24

Отзывы:

Похожие инструкции для E0-455-24

Бренды по названию

Популярные бренды

Taylor-Dunn E0-455-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание E0-455-24

Отзывы:

Похожие инструкции для E0-455-24

Бренды по названию

Популярные бренды