Taylor-Dunn C0-426-48AC Скачать руководство пользователя страница 55

Страница: 55 / 132

Brakes

Page 55

MC-425-15

C-426

MASTER CYLINDER

There are no internally serviceable components in the

master cylinder. If the master cylinder is faulty, it must

be replaced

Add Fluid

1: Thoroughly clean the area around the master

cylinder cap and remove the cap.

2: Add brake fluid from a new sealed container to

the master cylinder until it as the maximum level

line molded in the reservoir.

Adjust Push Rod

1: Tighten the master cylinder push rod pivot bolt so

that the push rod pivots freely with no side play.

2: Tighten the spring mounting bolt and the pedal

stop bolt so that one thread shows beyond the

locknut. See arrows in the illustration.

3: Tight the brake pedal pivot bolt so that the brake

pedal moves freely with no side play.

4: Test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Level lines are highlighted in the illustration for

clarity. They are not black.

PARKING BRAKE

The parking brake is an electromagnetic brake in the

drive motor. Refer to the motor section for information

on the brake.

Note: There is no adjustment to the brake.

Spring mounting bolt and the pedal stop bolt

Содержание C0-426-48AC





































































































































Результаты поиска

Содержание C0-426-48AC

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn C0-426-48AC, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание C0-426-48AC

Отзывы:

Бренды по названию

Популярные бренды