Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 49

Страница: 49 / 188

Transaxle

Page 49

MB-210-13

B-200 & B-210 Models

REMOVE

1: Release the park brake.

2: Remove the park brake cables from the spring axle mounting brackets and

brake arms.

3: Disconnect the wiring from the motor.

4: Disconnect the hydraulic brake lines from the left and right brake bodies.

5: Remove the nuts from the left and right side lower spring hanger bolts. Do

not remove the bolts at this time.

6: Raise the rear of the vehicle just high enough so that there is no tension on

the spring hanger bolts. Do not remove the bolts at this time.

7: Remove the four u-bolts holding the spring to the axle tubes.

8: Remove the two lower spring hanger bolts and raise the vehicle high enough to remove the drive and

support the frame with jack stands.

INSTALL

Install the transmission assembly in reverse order of removal.

•

a. Bleed the brake system. Refer to section Brake Service for information regarding bleeding the brakes.

•

b. Adjust the park brake. Refer to section Brake Service for information regarding adjusting the park brake.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды