Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 48

Страница: 48 / 188

Transaxle

Page 48

B-200 & B-210 Models

MB-210-13

CHECK OIL LEVEL

Fluid type and capacities are listed in the Lubrication

chapter.

1: Park the vehicle on a level surface and block the

front wheels.

2: Place a level on top of the motor.

3: Raise the rear of the vehicle until the level

indicates that the drive is level with the ground.

4: Place an oil drain pan underneath the 3rd

member.

Remove the 3rd member fill/level plug.

6: The oil level should be very close to the bottom of

the level plug opening.

•

If the oil level is below the bottom of the

opening, add oil as required until level with the

bottom of the opening. Refer to Lubrication

section for oil specification.

•

If oil comes out of the opening, allow to drain

until level with the bottom of the opening.

Replace the fill/level plug. Torque to the

specification listed in the table at the end of this

section.

Remove the primary reduction case fill/level plug.

9: The oil level should be very close to the bottom of

the level plug opening.

•

If the oil level is below the bottom of the

opening, add oil as required until level with the

bottom of the opening. Refer to Lubrication

section for oil specification.

•

If oil comes out of the opening, allow to drain

until level with the bottom of the opening.

10: Reconnect the batteries and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

CHANGE OIL

Fluid type and capacities are listed in the lubrication

section in the General Maintenance chapter.

1: Raise the rear of the vehicle and support with

jack stands.

2: Place a drain pan under the 3rd member and

primary reduction gear case.

3: Remove the drain plugs from the 3rd member

and primary reduction gear case.

4: Replace the drain plugs once the oil has drained.

Torque to the specification listed in the table at

the end of this section.

5: Remove the 3rd member and primary reduction

fill/level plugs and fill with oil.

•

Refer to Check Oil Level procedure for proper

oil level.

• Refer to Lubrication section for oil specification.

Replace the fill plug.

7: Reconnect the batteries and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды