Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 42

Страница: 42 / 188

Drive Axle-GT

Page 42

B-200 & B-210 Models

MB-210-13

PRIMARY GEAR CASE

1: Disconnect the batteries.

2: Raise the rear of the vehicle and support with jack

stands.

3: Place a drain pan under the gear case that is

capable of holding 4 liters (4 quarts) of oil and drain the oil from the front

gear case.

4: If required, remove the drive assembly from the vehicle. Refer to Remove

assembly procedure.

5: Remove the motor only if the entire drive is to be disassembled. Refer to

Motor procedure.

6: Remove the cover retaining bolts.

7: Remove the cover plate and let the remaining oil drain from the housing.

8: Remove the circlip from the idler gear.

9: Remove the input shaft/bearing assembly and idler gear/bearing assembly

from the gear case cover at the same time.

10: Remove the pinion nut from the output gear and remove the output gear

from the pinion shaft.

Note: If necessary, remove the seal from the input shaft bore at this time.

11: Mark the gear case position in relation to the 3rd member housing so that it

will be reassembled in the same position.

12: Remove the six retaining bolts holding the gear case to the 3rd member

housing.

13: Remove the gear case housing from the 3rd member housing.

14: Inspect all parts for signs of wear or damage.

15: Assemble the gear case in reverse order.

a. See note regarding special washers at the end of this section.

b. Apply gasket sealer (#94-430-05) to the front flange on the 3rd member and gear case cover.

c. Pack the motor seal with non-acetic based grease.

d. Torque the drain plug, gear case to 3rd member bolts, and pinion nut per torque listed in the Hardware Torque

table at the end of this section.

16:

Fill the differential with oil. Refer to Check Oil Level for information on filling the drive with oil.

17: Lower the vehicle.

18: Reconnect the batteries.

19: Remove the blocks from behind the wheels.

20: Test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Idler Gear Circlip

Remove Idler & Input Assy.

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды