Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 38

Страница: 38 / 188

Drive Axle-GT

Page 38

B-200 & B-210 Models

MB-210-13

CHECK OIL LEVEL

Fluid type and capacities are listed in the Lubrication

chapter.

Note: The oil flows freely between the main

gear case (3rd member) and the primary

reduction gear case. It is only necessary to

check the oil level of the 3rd member.

1: Park the vehicle on a level surface and block the

front wheels.

2: Disconnect the batteries.

3: Place a level on top of the motor.

4: Raise the rear of the vehicle until the level

indicates that the drive is level with the ground.

5: Place an oil drain pan underneath the 3rd

member.

Remove the fill/level plug.

7: The oil level should be very close to the bottom of

the level plug opening.

a. If the oil level is below the bottom of the opening,

add oil as required until level with the bottom of

the opening. Refer to the Lube Chart section for

information regarding type of oil.

b. If oil comes out of the opening, allow to drain until

level with the bottom of the opening.

Replace the fill/level plug.

9: Reconnect the batteries.

10: Remove the blocks from the wheels.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

CHANGE OIL

Fluid type and capacities are listed in the lubrication

section in the General Maintenance chapter.

1: Raise the rear of the vehicle and support with

jack stands.

2: Place a four quart drain pan under the axle

assembly center section.

3: Remove the drain plugs from the differential case

and gear case.

4: Replace the drain plugs once the oil has drained.

Remove the differential gear case fill/level

plug and fill with oil. Refer to Check Oil Level

procedure for proper oil level.

Replace the fill plug.

7: Reconnect the batteries.

8: Remove the blocks from the wheels.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Primary reduction case drain plug

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды