Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 32

Страница: 32 / 188

Front Axle

Page 32

B-200 & B-210 Models

MB-210-13

INSPECT FRONT WHEEL
BEARINGS

1: Raise the front of the vehicle and support with

jack stands.

2: Grab the top and bottom

of the tire/wheel assembly.

Feel for any movement

or play while pulling and

pushing on the top and

bottom of the tire. Any

movement or play is

indication of loose wheel

bearings.

3: Spin the front wheel(s) by

hand. The wheel should stop spinning in no more

than 2-revolutions. A wheel that continues to spin

freely is an indication of a loose wheel bearing.

Note: Refer to the Adjust Front Wheel Bearings

section for detailed information regarding the

proper adjustment of the wheel bearings.

4: Spin the wheel(s) and listen for any grinding

noise. Any noise may be an indication of worn or

damaged wheel bearings.

Note: Refer to the Replace Front Wheel Bearings

section for information regarding the

replacement of the wheel bearings.

5: Lower the vehicle.

6: Reconnect the batteries.

7: Remove the blocks from behind the wheels.

8: Release the park brake and test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

ADJUST FRONT WHEEL BEARINGS

•

The bearings must be lubricated before performing

this procedure.

1: Raise the front wheel(s) off of the ground and

support with jack stands.

While rotating the wheel

, tighten the front axle

nut until the wheel is difficult to rotate.

3: Continue to rotate the wheel for 5 compete

revolutions.

4: Attach a rope to the tire and wrap around the tire

with 1 foot remaining hanging in the air.

5: Tie a weight (see table and illustration below) to

the end of the rope.

6: Slowly loosen the axle

nut until the hanging

weight rotates the

wheel then rotate to

the nearest flat and

install a new cotter pin.

7: Remove the rope and

weight.

8: Spin the wheel and listen for any grinding noise.

Any grinding noise may be an indication of worn

or damaged wheel bearings.

Note: Refer to the Replace Front Wheel Bearings

section for information regarding the

replacement of the wheel bearings.

9: Lower the vehicle.

10: Reconnect the main positive and negative cables

at the batteries.

11: Remove the blocks from behind the wheels.

12: Release the park brake and test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Tire Size

Weight NEW

(pounds / kg)

Weight USED

(pounds / kg)

4.80 x 8

2.15 / 0.975

1.00 / 0.454

5.70 x 8

1.99 / 0.902

0.93 / 0.422

4.00 x 8

2.15 / 0.975

1.01 / 0.485

500 x 8

1.99 / 0.902

0.93 / 0.422

8.50 x 8

2.02 / 0.916

0.94 / 0.426

8 x 2.50

4.23 / 1.919

1.97 / 0.894

10 x 3.5

3.38 / 1.533

1.56 / 0.708

NEW: Weight = 16.931 / Radius
USED: Weight = 7.875 / Radius

3-Wheel vehicle front fork shown for illustration

purposes only

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды