Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 109

Страница: 109 / 188

Batteries

Page 109

MB-210-13

B-200 & B-210 Models

CLEANING

Disconnect the batteries before cleaning.
Dry dirt can be readily blown off with low-pressure air

or brushed off.

Note: Wetness or wet dirt on the top of the battery

indicates battery acid boil over or excessive

gassing.

Using a nonmetallic brush with flexible bristles, wash

the battery off with a strong solution of baking soda and

hot water mixed with a ratio of one pound of soda to

one gallon of water (0.5 kg / 3.7 liters). Continue until

all fizzing stops, which indicates that the acid has been

neutralized. Then rinse thoroughly with clear water. DO

NOT get any of the solution into the battery cells.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter and beginning of this

section..

WARNING

WATERING

Note: The electrolyte level in a battery rises while

charging and will be close to its highest

level after the end of a charging cycle. It is

recommended to fill the battery at the end of

a charging cycle. If the electrolyte is below

the top of the battery plates then fill just

enough to cover the plates and then top off

when the charging cycle is complete.

Clean the battery. Refer to Cleaning section for

information on cleaning the battery.

Check the electrolyte level in all battery cells. If low, fill

to the correct level (see illustration) with distilled water

using part number 77-201-00 battery filler, never add

additional battery electrolyte to the batteries.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter and beginning of this

section..

WARNING

DO NOT attempt to add water to a sealed battery.

Removing the caps of a sealed battery will damage

the battery resulting in premature failure.

NOTICE

CHARGING

Refer to the Operator manual for information regarding charging the battery.

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды