Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 108

Страница: 108 / 188

Batteries

Page 108

B-200 & B-210 Models

MB-210-13

GENERAL GUIDELINES AND SAFETY

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

•

Explosive mixtures of Hydrogen gas are present

within battery cells at all times. Do not work

with or charge battery in an area where open

flames (including gas furnace or water heater

pilots), sparks, cigarettes, or any other sources

of combustion are present. Always provide ample

ventilation in rooms where batteries are being

charged. Failure to do so may result in severe

bodily injury and/or property damage.

•

A battery is a live electrical source. It cannot be

disconnected or neutralized. Do not drop any

tool or conductive object onto the battery. A

conductive object that comes in contact with the

battery terminals will initiate a short circuit of the

battery. This could cause the battery to explode

resulting in severe bodily injury and/or property

damage.

•

Battery electrolyte is poisonous and dangerous.

It contains sulfuric acid. Avoid contact with skin

eyes or clothing. Wear rubber gloves and safety

glasses while servicing batteries. DO NOT INGEST!

This may result in severe bodily injury.

WARNING

Battery electrolyte will stain and corrode most

surfaces. Immediately and thoroughly clean any

surface outside of the battery that the battery

electrolyte comes in contact with. Failure to clean

may result in property damage.

NOTICE

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей, Страница: 108 / 188

Результаты поиска

Содержание B0-200-00

Отзывы: