background image

©Copyright Task Force Tips, Inc. 2011-2012 

LIA-520 April 25, 2011 Rev01

7

3.8 POWER SAVE MODE

The Hydrant Master is equipped with a power save mode. The valve automatically enters the power save mode when no buttons 
have been pressed for fi ve minutes. The display and backlighting will turn off. The valve position feedback system will continue 
to update and fl ash the current position every 3 seconds. To exit power save mode, push either the open or closed button.  The 
handheld remote control will automatically power down after fi ve minutes of no button presses. Turning the handheld remote control 
back on will not change the valve’s position.

3.9 VALVE POSITION INDICATOR & MECHANICAL OVERRIDE

The valve is equipped with a valve indicator which shows the position of the control valve. The sliding plug will be open when the 
control valve is open and there is more than 5psi (0.3 bar) pressure. The valve indicator can be used as a mechanical override In 
case of electronic failure. Swing the arm to the open position to open the valve or to the closed position to close the valve. 

VALVE POSITION INDICATOR

AND MECHANICAL OVERRIDE

CLOSED POSITION

OPEN POSITION

FLOW CONTROL POSITION

3.10 FLOW CONTROL FEATURE

The Hydrant master is equipped with a fl ow controlling program to maintain a maximum fl ow of 1000 gpm for the fi rst 15 seconds 
the valve is opening.  The valve position indicator will move to the full open position, move back to the fl ow control position, and then 
return to the full open position after 15 seconds. The fl ow controlling program prevents a hose line from charging at a rapid rate and 
helps avoid water hammer situations. 

WARNING

Minimum operating pressure 5 psi (0.3 bar).  Inadequate water pressure will prevent valve from 
opening and may result in a lack of water fl ow and cause injury or death to persons dependant on 
water fl ow.  Ensure there is adequate water pressure supplied to inlet of valve.

3.11 AUTOMATIC DRAIN

The Hydrant Master is equipped with an automatic drain that will empty trapped water from the main waterway of the valve.  The 
automatic drain closes when the internal pressure is approximately 5 psi (0.3 bar) or above and opens when the internal pressure 
is below 5psi (0.3 bar).

3.12 AIR FLUSH PORT

The valve is equipped with an air fl ush port.  Remove the cap.  Use a standard air chuck to apply a minimum of 20 psi (1.4 bar) to the 
air fl ush port.  Open and close the control valve.  Residual water will be forced out through the fi lter and control valve bleed drain.

CAUTION

The sliding plug is pinch hazard that can cause injury. Keep hands and fi ngers outside of the 
valve any time air is applied to air fl ush port. 

Содержание HYDRANT MASTER

















Отзывы: