Tascam US-366 Скачать руководство пользователя страница 15

Страница: 15 / 35

TASCAM US-322/366

4 – Connections

USB connections

Use the included USB cable to connect the US-322/366 to your

computer as shown in the illustration. When the USB connection

is active, the USB indicator on the top of the unit lights.

CAUTION

Some USB devices access the USB bus frequently. To

avoid dropouts and clicks in the audio signal, we strongly

recommend that you do not connect any USB devices other

than keyboards and mice to the USB bus used by this unit.

Audio connections

Connect the output signal of your mic, guitar, keyboard, or other

audio device to the US-322/366, where it will be converted

into digital audio and sent via USB to your computer. Connect

the output of the US-322/366 to your speakers (via an amp) or

headphones, so you will be able to monitor the audio signals

coming into the US-322/366 or being produced by your

computer.

CAUTION

Before connecting an audio device, set the

INPUT 1/2,

PHONES

and

LINE OUT

knobs to their minimum values.

Failure to do so could cause loud noises, which might

damage equipment or harm the hearing of people nearby.

Microphones

Connect microphones to the INPUT 1/L and INPUT 2/R MIC

connectors (XLR) on the front panel.
When using a condenser microphone that requires phantom

power, set the 48V switch on the front panel to ON.
When the 48V switch is set to ON, the 48V indicator on the top

panel lights.

48V indicator

CAUTION

•

Connecting a dynamic microphone with an unbalanced

connection to the unit when the

48V

switch is

could

damage this unit and make it unusable.

•

Do not connect or disconnect a mic with an input when this

switch is

. Loud noises might be produced and damage

could be caused to equipment.

•

Before turning a

48V

switch

OFF

, turn the output

volume down using the

PHONES

and

LINE OUT

knobs on

the front panel. Depending on the mic, loud noises might be

produced and damage could be caused to equipment or to

people’s hearing.

•

Always set the

48V

switch to

OFF

before turning the unit’s

power on or off (connecting or disconnecting the AC

adaptor).

•

Do not use phantom power when line level equipment is

connected to an XLR connector. It might damage equipment.

Guitars

Connect a guitar or bass guitar to the INPUT 1/L LINE/GUITAR

jack on the front of the unit and set the MIC/LINE-GUITAR

switch on the top to GUITAR.

Содержание US-366




































Результаты поиска

Содержание US-366

Отзывы:

Похожие инструкции для US-366

Бренды по названию

Популярные бренды

Tascam US-366, Руководство пользователя

Результаты поиска

Содержание US-366

Отзывы:

Похожие инструкции для US-366

Бренды по названию

Популярные бренды