TASCAM MZ-223
13
Operation procedures
After turning the power on, adjust the levels of the
input signals.
Adjusting line input channels (1–5)
1.
Set the channel 1–5
GAIN
knobs (
j
) to their cen-
ter positions.
2.
Press the channel 1–5
SOURCE SELECT
switches
(
0
), so that the
SOURCE SELECT
indicator (
A
/
B
)
lights.
3.
Press the channel 1–5
OUTPUT SEL
switches (
o
)
to select the output channel stereo buses (1–3)
that receive the input signals of each channel.
4.
When connecting an audio device to channel 1–2
LINE A
/
B
(
b
) input jacks, set the
LINE/PHONE
switch (
l
) to
LINE
.
5.
Set the
OUTPUT VOL
(
q
) knob levels low.
6.
Start playback on the connected audio device.
Use the
GAIN
knobs (
j
) to adjust the levels so
that the channel 1–5
PEAK
indicators (
9
) do not
light red.
7.
Follow the above procedures to adjust other line
input channels with connected audio devices.
Adjusting the inputs of mics connected
to the MAIN MIC 1–2 INPUT jacks
1.
Connect a mic to a
MIC 1–2 INPUT
jack (
1
), and
press the
MIC 1–2
switch (
7
) so that the
MIC 1–2
indicator (
7
) lights.
2.
Press
OUTPUT SELECT
switches (
2
) to select
outputs for signals input through the
MIC 1–2
INPUT
jacks (
1
).
3.
While checking the
MIC 1–2 INPUT
(
5
) and
PEAK
(
4
) indicators, use the
MIC 1–2 INPUT
VOLUME
knobs (
3
) to adjust the mic input lev-
els.
4.
Use the
MIC 1–2 INPUT EQ
knobs (
6
) to adjust
the 3-band (HIGH/MID/LOW) equalizers.
Output channels
Output signals can be sent to the following jacks from
the stereo output bus after the output equalizer.
0
MAIN OUTPUTS 1–3 (UNBALANCED)
(
v
) and
MAIN OUTPUTS 1–3 (BALANCED)
(
c
) jacks
0
MONITOR OUT
jacks (
x
)
NOTE
The output level from the
MONITOR OUT
(
x
)
jacks cannot be adjusted.
Adjusting the levels output from the MAIN
OUTPUTS 1–3 (UNBALANCED) and MAIN
OUTPUTS 1–3 (BALANCED) jacks
While checking the output level indicators (
w
), use
the channel faders (
8
) and
OUTPUT VOL
(
q
) knobs
to adjust the output levels. The optimal output level
adjustment is usually when the output level indica-
tors (
w
) light around 0 dB.
When an amplifier is connected to the
MAIN OUT-
PUTS 1–3 (UNBALANCED)
(
v
) or
MAIN OUTPUTS
1–3 (BALANCED)
(
c
) jacks, set the
ATTENUATOR
(
h
)
switch to
OFF
if it accepts high gain or
ON (-6dB)
if it
accepts low gain.
Use the
OUTPUT EQ
knobs (
e
) to adjust the 3-band
(HIGH/MID/LOW) equalizers for the output sound.
Using the talkover function
When the talkover function is turned on by pressing
the
TALKOVER ON
switch (
i
), the levels of channels
1 will be automatically lowered when sound is input
from a mic connected to a
MIC 1–2 INPUT
(
1
) jack,
making the mic signal easier to hear.
To turn the talkover function off, press the
TALKOVER
ON
(
i
) switch to disable it (
TALKOVER ON
(
i
) indi-
cator becomes unlit).
Use the
TALKOVER DAMP
(
y
) and
TALKOVER TIME
(
u
) knobs to adjust the attenuation level and re-
sponse time.
Listening to channel pre-fader signals
By pressing the
PFL
(
p
) switches of channels to turn
them on, you can enable headphone monitoring of
individual channels 1–5, even when their faders (
8
)
are set at minimum values.
1.
Press PFL
(
p
) switches so that their
PFL
indica-
tors light, and turn the
MIXING
(
d
) knob to
PFL
.
To monitor the signal before it is sent to the
stereo output bus, turn the
MIXING
(
d
) knob to
MONITOR
.
2.
Use the
PHONES VOLUME
(
a
) knob to adjust
the monitoring output level.
Содержание MZ-223
