• Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated could destroy the product. Allow
the device to reach room temperature before connecting and using it. This may
take several hours.
• Never operate the product unattended.
•
The housing heats up during operation. Ensure sufficient ventilation. The housing
must not be covered!
• Do not short-circuit the USB connectors.
• Do not charge the product from a USB port of a computer or other products since
the power provided is insufficient. This can cause damage to the connected
product.
• Consult an expert when in doubt about operation, safety or connection of the
device.
•
Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Rechargeable batteries
• The rechargeable battery is permanently built into the product and cannot be
replaced.
• Never damage the rechargeable battery. Damaging the casing of the rechargeable
battery might cause an explosion or a fire! Unlike conventional batteries/
rechargeable batteries (e.g. AA or AAA type), the casing of the LiPo rechargeable
battery does not consist of a thin sheet but rather a sensitive plastic film only.
• Never short-circuit the contacts of the rechargeable battery. Do not throw the
battery or the product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the
product. Due to the rechargeable battery technology being used, you do not need
to discharge the rechargeable battery first.
• Never charge the rechargeable battery of the product unattended.
• When charging, place the product on a surface that is not heat-sensitive. It is
normal that a certain amount of heat is generated during charging.
Operating elements
1 USB-A output
OUT1 1.0 A
2 Micro USB input
IN 2 A
3 Battery level indicator
4 Function button
5 USB-A output
OUT2 Smart
1
4
3
5
2
Operation
Check the internal battery charge level before each use.
Make sure the connection values of your mobile device match those of the product
(see technical data).
The USB cable is not suitable for data transfer.
Remove any protective films from the product.
a) LED indicator of the battery charge level
Press the function button
(4)
to check the battery level. The remaining capacity on the battery
level indicator
(3)
is indicated by the lit LEDs as follows:
1 LED
Remaining capacity up to 25 %
2 LEDs
Remaining capacity up to 50 %
3 LEDs
Remaining capacity up to 75 %
4 LEDs
Remaining capacity up to 100 %
The LED that indicates the current battery level flashes while charging.
b) Charging the battery
•
When using for the first time, it is recommended to fully charge the portable charger once.
•
Charge the portable charger at the latest when only one LED lights up and/or the battery
level falls below 25 %.
• To charge the portable charger, a USB charger (not included) is required. A USB charging
cable (Micro USB to USB-A) is included. Connect the Micro USB connector to the Micro USB
input
IN 2 A
(2)
. Connect the USB-A connector of the USB charging cable to a USB-A port of
a USB charger (not included). Observe the technical data.
A USB charger with 2 A is recommended for the portable charger input current. If a
lower input current is used, charging will take longer. However, a higher input current
than 2 A (Micro USB) will not reduce the charging time since the input current is
limited.
• The charging time of the portable charger can be up to approx. 5 - 5.5 hours with a 2 A USB
charger via the Micro USB input with a remaining battery capacity of approx. 20 %. While
charging, the current battery level will be indicated by the corresponding flashing LED.
• Once the battery is fully charged, the battery level indicator LEDs will be lit steadily.
• Disconnect the connected cables.
Operating instructions
Portable charger 8000 S
Model no. 1002BTF
Item no. 1002BTF
Intended use
The product serves as a spare battery for mobile devices (for example, smartphone, tablet)
with 5 V/DC voltage. The portable charger has two USB-A outputs that can be used to charge
suitable devices. To charge the portable charger, a USB charger (not included) is required. The
included Micro USB charging cable can be used to charge the internal battery. The product has
a battery level indicator and is protected against overcharging and short circuit.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Portable charger
• USB charging cable (Micro USB to USB-A)
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link
www.conrad.com/downloads
or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of
personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
