TANDBERG SM6610 Скачать руководство пользователя страница 74

Страница: 74 / 200

Operating the Equipment Locally – Main Menu Option 4: System Menu

Page 3-36

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

ST.RE.E10152.2

Serial Port Configuration Option 2: Set Port Mode

Type 2 at the prompt to view the

Set Port Mode

menu from the

Serial

Port Configuration Menu

. This option allows the serial port to be

configured for either terminal or remote control.

TANDBERG Television SM6600 Satellite Modulator: DEV001

Port Mode

1 Set Mode to Terminal

2 Set Mode to Remote

H Help

Q Quit

Status: No Alarms

Please enter your selection, then press Enter:

Table 3.4: Set Port Mode Options

Command Messages

Description

Set Mode to Terminal

Port mode updated. This change
requires the modulator to be rebooted.

Select this option to allow control of the
Modulator by means of a VT100 terminal.

Set Mode to Remote

Port mode updated. This change
requires the modulator to be rebooted.

Select this option to allow remote control of the
Modulator via the RS-232/485 port using either
the RS-232 or the RS-485 remote control
protocol. See Chapter 5, RS-232 Remote
Control Protocol and Chapter 6, RS-485 Remote
Control Protocol.

Serial Port Configuration Option 3: Select Interface
Type 3 at the prompt to view the

Select Interface

menu from the

Serial Port Configuration Menu

. This option allows the port to be

configured as either an RS-232 or RS-485 port.

Select Interface

Serial Port is configured as RS-232

1 RS-232

2 RS-485

Please enter your selection, then press Enter:

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Бренды по названию

Популярные бренды