TANDBERG SM6610 Скачать руководство пользователя страница 53

Страница: 53 / 200

Operating the Equipment Locally – Main Menu Option 1: Quick Setup Menu

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators

Page 3-15

ST.RE.E10152.2

Quick Setup Menu Option 6: Coding Mode

This is intended for future functionality. Currently, its setting cannot be

changed.

Coding Mode : Current Value= "DVB"

1 DVB

Quick Setup Menu Option 7: Modulation

Modulation : Current Value= "QPSK"

1 BPSK

2 QPSK

3 *8PSK* FEC Rate : ->8/9

4 16QAM

NOTES…
1.

In the above display, asterisks show that the currently set FEC Rate is not valid for this

modulation and 8/9 will be set automatically.

8PSK and 16QAM modulations are only available with the HOM option.

Quick Setup Menu Option 8: FEC Rate

The output data are coded by the addition of convolutional Forward Error

Correction (FEC) bits, enabling errors which occur in the transmission

process to be corrected at the receiver (see Chapter 7, Equipment

Description, Forward Error Correction and Interleaving for further

information).
Six FEC options are provided: a value of

⁄

gives the highest error-

correction capability but has the largest overhead in bit-rate;

⁄

gives the

lowest error-correction capability but has the smallest overhead in bit-rate.

The allowable FEC values are dependent upon the Modulation currently

selected.

FEC Rate : Current Value= "3/4"

1 1/2

2 2/3

3 3/4

4 5/6

5 7/8

6 *8/9* Modulation : ->8PSK

NOTE…
In the above display, asterisks show that the currently set Modulation is not valid for this FEC Rate and

8PSK will be set automatically.

Quick Setup Menu Option 9: Roll-off

This parameter is used for selection of the roll-off factor of the Modulator’s

spectrum-shaping filters. ETSI standards EN 300 421 (DVB-S) and

EN 301 210 (DVB-DSNG) specify a roll-off factor of 35%. EN 301 210

optionally specifies a roll-off factor of 25% for use with 8PSK and 16QAM

modulations.

Содержание SM6610









































































































































































































Результаты поиска

Содержание SM6610

Отзывы:

Бренды по названию

Популярные бренды

TANDBERG SM6610, Справочное руководство

Результаты поиска

Содержание SM6610

Отзывы:

Бренды по названию

Популярные бренды