background image

  

Installing the Equipment 

Reference Guide: SM6610, SM6615, SM6620 and SM6625 Satellite Modulators 

Page 2-15 

ST.RE.E10152.2 

L-Band Output (Main) 

50 

 SMA socket provides an L-band output. 

Table 2.12: L-Band Output Connector (Main) 

Item Specification 

Connector type 

SMA 50 

 Female 

Type Analogue 

Connector designation 

L-BAND OUT MAIN 

Pin-outs 

Centre 
Screen 

L-Band Output 
Ground 

L-Band Output (Monitor) 

75 

 F-type socket provides an L-band output used for 

monitoring. 

Table 2.13: L-Band Output Connector (Monitor) 

Item Specification 

Connector type 

F-type 75 

 Female 

Type Analogue 

Connector designations 

L-BAND OUT MONITOR 

Pin-outs 

Centre 
Screen 

L-Band Output 
Ground 

2.5.7 

S13450 DVB ASI & SPI Input Card (Option) 

Rear Panel View 

 

Figure 2.11: S13450 DVB ASI & SPI Input Card Connections 

DVB ASI Electrical Inputs 

Two BNC, female 75 

 connectors provide DVB-compliant 

ASI electrical connections at a fixed line transmission rate 

of 270 Mbit/s. 
 
 
 
 

 

 

 

Содержание SM6610









































































































































































































Отзывы: