TANDBERG Media Processing System MPS 800 Скачать руководство пользователя страница 36

Страница: 36 / 179

D 13373.08
NOVEMBER 2007

MPS

Table of

Contents

TANDBERG

MPS

ADMINISTRATOR GUIDE

The Using the MPS section will help you understand how to use the

MCU, Gateway and Phone Book. It provides a step-by-step guide to
the basics as well as a description of each setting available from the
web interface.

We recommend that you check the
TANDBERG web site regularly for updated
versions of this manual:

http://www.tandberg.com/support/
documentation.php

Using the MPS

MPS 200

MPS 800

Introduction

Quick

Setup

System

Status

System

Configuration

Installation

Gateway

Configuration

MCU

Configuration

Technical

Descriptions

Appendices

Main

Using

the MPS

Содержание Media Processing System MPS 800




















































































































































































Результаты поиска

Содержание Media Processing System MPS 800

Отзывы:

TANDBERG Media Processing System MPS 800, Руководство администратора, Страница: 36 / 179

Результаты поиска

Содержание Media Processing System MPS 800

Отзывы: