background image

432549-01

Quick Start Guide

SuperLoader

For more information about Tandberg Data´s

quality products, visit www.tandberg.com 

Tandberg Data

 publications can be requested from a 

Tandberg Data

 Sales Representative or ordered directly from 

For the latest information about Super DLTtape™ and DLTtape™ products and accessories, visit the 

Tandberg Data

web 

site at www.

tandberg

.com or the Technical Support site at www.dlttape.com.

Tandberg Data

 reserves the right to make changes and improvements to its products, without incurring 

any obligation to incorporate such changes or improvements in units previously sold or shipped.

Publication Number: 

4325

49

-0

1

© 2002 

Tandberg Data

. All rights reserved. 

Tandberg Data and

 the 

Tandberg Data

 logo

 are trademarks of Tandberg

 

Data ASA. The DLTtape logo and the Super DLTtape logo are trademarks of Quantum Corporation, registered
in the U.S.A. and other countries. DLTtape, Super DLTtape, SuperLoader, and the SuperLoader logo are
trademarks of Quantum Corporation. Products mentioned herein are for identification purposes only and may be
trademarks or registered trademarks of their respective companies. All other trademarks are the property of their

Tandberg Data.

respective owners.

 

Содержание SUPERLOADER















Отзывы: