Taktomat LFA Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 39

Taktomat LFA Скачать руководство пользователя страница 25

Maintenance

Version 1.0

Linear transfer system LFA

25 / 39

7

Maintenance

Required personal protective equipment

DANGER

Electric shock

Touching live parts poses an immediate danger to life

•

Work on electrical systems may only be carried out by qualified electricians

•

Before starting work, disconnect the system, secure it against being switched on again and
make sure that no voltage is present

7.1

General

The maintenance intervals are minimum recommendations for three-shift use. Non-compliance with the maintenance
instructions and unauthorized modifications will render warranty claims and the manufacturer's liability void.

Comply with all laws, regulations as well as the regulations of the respective country of operation for the protection of people
and the environment.

The maintenance instructions are only valid in conjunction with the instructions of the respective manufacturer. The contents
are subject to change without notice.

7.2

Maintenance tasks

Carry out switch-on and switch-off procedures in accordance with the instructions for all maintenance and cleaning work.

Observe the adjustment, maintenance and inspection activities prescribed in the operating and maintenance instructions,
including the specifications on parts/equipment replacement.

Ensure that the maintenance area is adequately secured if necessary.

Rework

When carrying out maintenance work, always retighten loosened screw connections.

If it is necessary to remove any safety equipment, the safety equipment must be reinstalled immediately after the work has
been completed. After installation, check the function of the safety equipment.

Dispose of operating and auxiliary materials as well as cleaning agents and replacement parts safely and in an
environmentally friendly manner. Follow the manufacturer's instructions for hazardous substances.

Spare parts

Spare parts must comply with the technical requirements specified by the manufacturer. This is always ensured if genuine
spare parts are used.

Environmental protection

Remove leaking or excess grease from lubrication points and dispose of it in accordance with the applicable local regulations.

Assembly instruction

s

«
...
23
24
25
26
27
...
»

Содержание LFA








































Отзывы:

Нет отзывов