Taiden hcs-8300 Скачать руководство пользователя страница 99

Страница: 99 / 255

3.5.3 Connection

3.5.3.1 Connecting to 1000M Ethernet switcher

HCS-8338/8348 series New Generation Paperless

Multimedia Congress Terminal is based on the

TAIDEN

originated

GMC-STREAM Gigabit Multimedia

Congress Stream technology. All audio and video

signals are transmitted via a Cat.6 Gigabit network

cable. GMC-STREAM fully guarantees the real-time

performance and stability of the important data stream

of the meeting, such as audio, voting information, and

control information.

When connecting to 1000M Ethernet switcher, just

connect the “Delegate” port of the HCS-8300KMX to

“1000M Ethernet” port of the multimedia congress

terminal with a Cat.6 1000M Ethernet cable.

Figure 3.5.3 HCS-8338 series new generation paperless

multimedia congress terminal connecting to 1000M

Ethernet switcher

3.5.3.2 Connection between New Generation

Paperless Multimedia Congress Terminals

HCS-8338/8348 series new generation paperless

multimedia congress terminals are “daisy-chained” with

Cat.6 1000M Ethernet cable. When connecting to the

next terminal, just connect the port (1000M Ethernet) of

the terminal to the port (1000M Ethernet IN) of the next

terminal by means of a Cat.6 1000M Ethernet cable.

3.5.3.3 To external microphone

An external microphone is connected to the external

microphone jack at the lateral side of the multimedia

terminal. The external microphone shall have a Ø 3.5

mm plug, as in the following figure:

Functions and indications:

2 Suspend/Ground

3 Ground

3.5.3.4 To external earphone

An external earphone can be connected to the external

earphone jack at the lateral sides of the multimedia

terminal. Its volume is adjustable by the earphone

volume control key. The external earphone shall have a

Ø 3.5 mm plug, as in the following figure:

Functions and indications:

1 Left stereo channel signal

2 Right stereo channel signal

3 Power ground/Shield

Figure 3.5.4 Daisy-chain connection between HCS-8338 series New Generation Paperless Multimedia Congress Terminals

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды