Taiden hcs-8300 Скачать руководство пользователя страница 62

Страница: 62 / 255

2.2.3 Connection

HCS-8300 series CMU has two 6P-DIN output

interfaces; the power capacity of each 6P-DIN interface

is limited. If the actually needed power of the system

(that is, considering the actual total needed power

consumption of the connected congress units and

extension cables) is larger than the output capacity,

HCS-8300ME(/FS) extension main units are needed.

Each extension main unit has an extension input port

for connecting to extension interface of the congress

main unit, another extension output interface

connecting to the next extension main unit. Each

extension main unit has four 6P-DIN output interfaces

for connecting congress units, and dedicated 6 cord

cables are used for connection.

Figure 2.2.4 Connection between the CMU and EMU

Содержание hcs-8300
































































































































































































































































Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды

Taiden hcs-8300, Инструкция по установке и эксплуатации

Результаты поиска

Содержание hcs-8300

Отзывы:

Бренды по названию

Популярные бренды