Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 98

Страница: 98 / 142

TGW4/8 Gateway Series for Aeonix User Configuration Manual

Tadiran Telecom (TTL)_L.P. 86

Aeonix Configuration

It is necessary to define all FXS stations and FXO trunks in Aeonix, before any calls can be routed
through them. Trunks must be assigned to trunk groups to operate in the Aeonix system.

For detailed information, refer to the

Aeonix Administration Manual

Chapter 3, Getting Started > Licenses
Chapter 6, Managing Users
Chapter 7, Managing Phones
Chapter 8, Managing Trunk Groups

Chapter 9, Managing Trunks

3.1 License Requirements

Verify that you have the correct licenses.



FXS stations require the "

Aeonix Gateway users

" license



FXO trunks require the "

Aeonix SIP Trunks & Gateways (concurrent calls)

" license

Open the Aeonix Web Admin.

At the bottom of the navigation pane, click

System

. The pane displays the System menus.

Select the

License

menu, and then click

License

Figure 3-1

Aeonix License Information Page

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды