Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 81

Страница: 81 / 142

TGW4/8 Gateway Series for Aeonix User Configuration Manual

Tadiran Telecom (TTL) L.P. 69

Table 2-30

Clock Service Parameters

Name

Description

Time Zone

Select the relevant time zone:



(GMT-11:00) Midway Island



(GMT-10:00) Honolulu. Hawaii



(GMT-09:00) Anchorage, Alaska



(GMT-08:00) Tijuana



(GMT-06:00) Denver



(GMT-06:00) Mexico City



(GMT-05:00) Indianapolis



(GMT-04:00) Glace_Bay



(GMT-04:00) South Georgia



(GMT-03:30) Newfoundland



(GMT-03:00) Buenos Aires



(GMT-02:00) Cape_Verde



(GMT) London



(GMT+01:00) Amsterdam



(GMT+02:00) Cairo



(GMT+02:00) Israel



(GMT+02:00) Zimbabwe



(GMT+03:00) Moscow



(GMT+03:30) Teheran



(GMT+04:00) Muscat



(GMT+04:00) United Arab Emirates



(GMT+04:30) Kabul



(GMT+05:30) Calcutta



(GMT+05:00) Karachi



(GMT+06:00) Almaty



(GMT+07:00) Bangkok



(GMT+07:00) Indonesia



(GMT+08:00) Beijing



(GMT+08:00) Taipei



(GMT+08:00) Singapore



(GMT+08:00) Malaysia



(GMT+09:00) Tokyo



(GMT+10:00) Canberra



(GMT+10:00) Adelaide



(GMT+11:00) Magadan



(GMT+12:00) Auckland

Current time

Display current time for the TGW. Click

Clock calibration

to calibrate the time.

System time sync
interval

Set the synchronization period of the time. It is 120 minutes by default.

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды