Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 48

Страница: 48 / 142

User Configuration Manual TGW4/8 Gateway Series for Aeonix

36 Tadiran Telecom (TTL) L.P.

2.5.2 Trunk Features (TGW8-2G)

Only a gateway with FXO ports can display this interface.

After login, click the

Trunk > Trunk

tab to open the Trunk configuration interface.

Figure 2-20

Trunk Line Features Configuration Interface

Table 2-15

Configuration Parameters of Trunk Features

Note: * indicates mandatory parameters for Aeonix.

Name

Description

Trunk ID

Select the trunk line you want to configure. “FXO-n” corresponds to the

Trunk

Phone number

ID n

*
Phone number

Display phone number associated with the trunk set in

Trunk

Phone number.

See

ID n

on page 35.

Display as

Fill in the display name associated with this port.

Local SIP port

Set the port used for receiving and sending SIP messages on the line.
If this parameter is not specified, the local port configured in

Basic

SIP

is used.

This parameter is displayed only when

multi port

is selected in the

Advanced

SIP

page.

Registration

Select if this trunk registers with the SIP registration server. By default, this is not selected.

For Aeonix



Select this parameter.

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды