Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 142

Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 18

User Configuration Manual TGW4/8 Gateway Series for Aeonix

6 Tadiran Telecom (TTL) L.P.

Figure 1-4

TGW8-2G and TGW8S-2G Back Panel

Table 1-9

Description of TGW8-2G and TGW8S-2G Back Panel

Item

Description

FXO/FXS

FXS port or FXO port

AUX

Auxiliary RJ45 management interface, serves as the LAN interface to connect a PC with the
primary purpose for local management and configuration.

AUX port is considered as downlink port only

WAN

Ethernet RJ45 interface. It serves as a WAN interface to connect to internet.

WAN port is considered as uplink port only.

CON

The console port is used for local management and testing. PCs can be connected to TGW
by linking the RS232 port to CON port.
Connecting cables need to be produced or purchased.
If the connection is established between the TGW and the mobile PC with no RS232 ports,
use the cable together with a USB to an RS232 converter cable.
Cables are shown below in  Figure 1-5 and  Figure 1-6.

RST

To restore the TGW8-2G and TGW8S-2G to factory default, press the RST button for more
than 3 sec and release it when STU turns to blinking red. This setting will be valid after
rebooting the TGW.

PWR

Power interface, 12 VDC input

«
...
16
17
18
19
20
...
»

Содержание TGW4 SERIES















































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды