background image

iWorx® CSM1

502-045, Effective: July 25, 2013

© 2013 Taco Electronic Solutions, Inc.

Power (PWR)

Connect one output wire from a 24 VAC power supply to PWR (T39) and the other output wire from the power supply to 
the adjacent common terminal (T38).

Ground (GND)

Terminal GND

 

(T40) must be connected to earth ground. Failure to properly ground this equipment will 

result in improper operation. Improper grounding may also increase the risk of electrical shock, and may 
increase the possibility of interference with radio and TV reception.

SPECIFICATIONS

Electrical Inputs

Resolution:

 10

 bit 

Outside Air

 

Humidity, Inside Air Humidity, Supply Air Humidity:

 0-10

 Volts

 DC

Outside Air Temp, Hot Supply Water Temperature, Chilled Supply Water Temperature, Supply Air Temp:

 Precon 

Type III 10K thermistor

Energy

 Monitor, 

End

 of

 Interval:

 Normally open, Dry contact, 5

 

Volts DC Max

Unit Enable:

 Normally open (closed when active), Dry contact, 5

 

Volts DC Max

Recommended Sensor Wire 

Maximum Length:

 500 feet (152 meters) 

Recommended LON Bus FTT-10A Network Wire

Speed:

 78KBPS

Max Volts:

 42.4 Volts DC 

Cabling:

 Maximum node-to-node distance: 1312 feet (400 meters); Maximum total distance: 1640 feet (500 meters) 

Power

Requires:

 24VAC (20VAC to 28VAC), requires an external Class 2 supply

Consumes:

 7.2W with no external loads, maximum limited by the Class 2 supply rating

Mechanical

Dimensions:

 5.55” (141mm) high, 6.54” (166 mm) wide, 1.75” deep (44

 mm), 

ABS

Controller Weight:

 0.70

 pounds 

(0.32

 kilograms)

Shipping Weight:

 1.0

 pounds 

(0.46

 kilograms)

Processor:

 3150 Neuron 10 MHz

Flash:

 48

 Kilobytes 

Cable Type

Pairs

Details

Taco Catalog No.

18AWG 

1

Stranded Twisted Shielded Pair, Plenum

WIR-018

Cable Type

Pairs

Details

Taco Catalog No.

Level 4 22AWG (0.65mm)

1

Unshielded, Plenum, U.L. Type CMP

WIR-022

Содержание iWorx CSM1













Отзывы: