manualshive.com logo in svg

TA DISCOVERY DSC2500, Руководство по началу работы

Поделиться
Скачать
TA DISCOVERY DSC2500 Скачать руководство пользователя страница 44

Discovery DSC™ Getting Started Guide

Page 43

MISE EN GARDE: Un mauvais alignement de la pompe sur le réservoir peut endommager le 
bouchon d'étanchéité sous vide. Pour éviter le risque de gel du capuchon d'étanchéité à vide, la fig-
ure 26 montre l'orientation de la pompe vers le réservoir.

 Figure 26 

Pump and tank orientation.

Installing the LN Pump on the Discovery DSC

Installation of the LN Pump onto the Discovery DSC involves:

1

Removing the Discovery DSC covers

2

Mounting the cooling head

3

Connecting the heater cable

4

Replacing the covers

5

Connecting the cables and lines

This section provides the instructions for installing the LN Pump on the Discovery DSC. 

Remove the top cover on Discovery DSC 25, DSC 250, DSC 2500

1

If an Autosampler is present, it must be moved away from the cell by pressing the 

Lid Open/Close

 

 button on the user interface.

WARNING: Do not place your hands in the path of the Autosampler when it is in motion. Physi-
cal injury may occur. 

AVERTISSEMENT: Ne placez pas vos doigts sur le chemin de l'échantillonneur automatique 
lorsqu'il est en mouvement. Des blessures physiques peuvent se produire.

Return line

Supply line

Vacuum seal cap

Relief valves: DO NOT ALIGN 
OVER VACUUM SEAL CAP

Vent: DO NOT ALIGN 
OVER VACUUM SEAL CAP 

Содержание DISCOVERY DSC2500






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды