background image

Discovery TGA™ Getting Started Guide

Page 5

For United States

UL61010-1:2012 Electrical Equipment for Laboratory Use; Part 1: General Requirements.

UL61010-2-010:2015 Particular requirements for laboratory equipment for the heating of materials.

UL 61010-2-081:2015 Particular requirements for automatic and semi-automatic laboratory equipment for 
analysis and other purposes.

Electromagnetic Compatibility Standards

For Australia and New Zealand

AS/NZS CISPR11:2015 Limits and methods of measurement of electronic disturbance characteristics of 
industrial, scientific and medical (ISM) radio frequency equipment.

For Canada

ICES-001 Issue 4 June 2006 Interference-Causing Equipment Standard: Industrial, Scientific, and Medical 
Radio Frequency Generators.

For the European Economic Area

(In accordance with Council Directive 2014/30/EC of the European Parliament and of the Council of 26 
February 2014 on the harmonization of the laws of the Member States relating to electromagnetic 
compatibility.)

EN61326-1: 2013 Electrical equipment for measurement, control, and laboratory use - EMC requirements 
- Part 1: General requirements, Table 3 - Immunity test requirements for equipment used in controlled EM 
environments, Emission requirements for Group 1, Class A equipment.

For the United States

CFR Title 47 Telecommunication Chapter I Federal Communications Commission, Part 15 Radio 
frequency devices (FCC regulation pertaining to radio frequency emissions).

CAUTION: This equipment is not intended for use in residential environments and may not provide 
adequate protection to radio reception in such environments.

MISE EN GARDE: Cet appareil n'a pas destiné à être utilisé dans des environnements résidentiels et 
ne peut pas fournir une protection adéquate à la réception radio dans de tels environnements.

Содержание TGA5500





































































Отзывы: