T.J.M. T13 Outback Frontal Protection System Скачать руководство пользователя

Страница: 6 / 18

FITTING INSTRUCTIONS

Product:

T13 Outback Frontal Protection System

Vehicle:

Toyota LandCruiser 200 Series 2007+

Part No.

070SB13R82A

For further information contact T.J.M. Head Office on (07) 3865 9999. Distributors Australia

wide.

File: F-1434.docx

Page 6 of 18

11/12/2013

16.

Remove (& discard) the front intrusion

beam & mounting brackets from the

front of the chassis & lower bumper

retainers.

17.

Remove (& retain) the tow lugs

(discarding the fasteners).

18.

Remove (& discard) the shipping lugs.

19.

Remove (& retain) the front 2 underbody

guard fasteners.

20.

Fit the grille bracket to the upper bumper

support, using M8 x 1.25 x 20mm hex

bolts (2), M8 x Ø19mm flat washers (4)

& M8 nyloc nuts (2).

21.

Remove/Trim the bumper clips under the

headlight so that they will not interfere

with the headlight trim once it has been

fitted.

22.

Repeat the previous step for the opposite

side of the vehicle.

RHS SHOWN

UPPER BUMPER

SUPPORT

Содержание T13 Outback Frontal Protection System



















Результаты поиска

Содержание T13 Outback Frontal Protection System

Отзывы:

Похожие инструкции для T13 Outback Frontal Protection System

Бренды по названию

Популярные бренды

T.J.M. T13 Outback Frontal Protection System, Инструкция по монтажу

Результаты поиска

Содержание T13 Outback Frontal Protection System

Отзывы:

Похожие инструкции для T13 Outback Frontal Protection System

Бренды по названию

Популярные бренды