T.I.P. GPS 3200 Plus, Руководство по эксплуатации

Страница: 16 / 134

6
If the pump is to be put out of operation for some extended period of time, it should be emptied completely in by
opening the water drain screw (10). Subsequently, please flush the pump with clean water. Then allow the pump
body to dry completely in order to prevent corrosion damage.
Water left in the pump may freeze in case of frost and thus cause considerable damage. Please store the pump in
a dry, frost- protected place.
In the case of malfunction, you should first of all check whether it was caused by an operating error or some other
reason which cannot be attributed to a defect of the device - for instance a power failure.
The list below shows some possible malfunctions of the device, possible causes and tips on their elimination. All
the measures referred to may only be carried out with the pump being separated from the electrical mains. If you
yourself feel unable to eliminate any of these malfunctions, please contact the customer service department or
your point of sales. Any repair beyond the scope specified below must only be performed by qualified staff.
Please bear in mind that all warranty claims will become void in the case of damage caused by inappropriate
repair attempts, and that we decline any liability for any ensuing damage.
MALFUNCTION POSSIBLE CAUSE ELIMINATION
1. The pump is not
discharging any
liquid, the motor is
not running.
1.
2.
3.
4.
No current.
Thermal motor protection feature has
triggered.
The capacitor is defective.
The motor shaft is jamming.
1.
2.
3.
4.
Please use a device complying with GS
(German technical supervisory authority) to
check for the presence of voltage (safety
information to be observed!). Please verify the
correct position of the plug.
Separate the pump from the electrical mains,
allow the system to cool down, eliminate cause.
Please contact the customer service
department.
Check the cause, eliminate the reason for the
jamming of the pump.
2. The motor is running,
but the pump is not
discharging any
liquid.
1.
2.
3.
The pump housing is not filled with liquid.
Air penetrates into the intake line.
Suction height and/or discharge height too
great.
1.
2.
a)
b)
c)
d)
3.
Fill the pump housing with liquid (please refer to
”Putting into operation” section).
Check to make sure that:
the connection points of the intake line are tight;
the inlet opening of the intake line including the
check valve (non-return valve) are immersed
into the liquids being discharged;
the check valve (non-return valve) with the filter
is tight and not jammed;
no siphons (i.e. permanently liquid-filled loops),
kinks, counter-slopes or narrow spots are
present along the intake lines.
Change the arrangement of the installation so
that the suction height and/or discharge height
will not exceed the max. value.
3. The pump stops after
a short time of
operation because
the thermal motor
protection feature
has triggered.
1.
2.
3.
4.
The electrical supply does not correspond to
the information given on the type plate.
Pump or intake line are blocked by solids.
Liquid is too viscous.
Temperature of liquid or environment is too
high.
1.
2.
3.
4.
Please use a device complying with GS
(German technical supervisory authority) to
check the voltage of the lines of the connection
cord (safety information to be observed!).
Remove possible congestion.
Pump may not be suitable for this liquid. If
feasible, the liquid should be thinned.
Make sure that the temperature of the liquid
being pumped and the environment do not
exceed the max. admissible values.
4. The pump does not
reach the desired
pressure.
1.
2.
Refer to section 2.2.
Worn pump wheel.
1.
2.
Refer to section 2.2.
Please contact the customer service
department.
10. Warranty
The present device was manufactured and inspected according to the latest methods. The seller warrants for
faultless material and workmanship in accordance with the legal regulations of the country in which the device
was purchased. The warranty period begins with the day of the purchase and is subject to the provisions below:
Within the period of warranty, all defects which are to be attributable to defective materials or manufacturing will
be eliminated free of charge. Any complaints are to be reported immediately upon their detection.
The warranty claim becomes void in the case of interventions undertaken by the purchaser or by third parties.
Damage resulting from improper handling or operation, incorrect setting-up or storage, inappropriate connection
or installation or Acts of God or other external influences are excluded from warranty.
Parts being subject to wear and tear, such as the pump wheel (impeller) and mechanical shaft seals are excluded
from warranty.
All parts were manufactured using maximum care and high-quality materials and are designed for a long lifecycle.
It should be understood, however, that the wear and tear depends on the kind of use, the intensity of use and the
13