background image

Page 9

English

Safety

Respiratory system protection

Storage

Protective clothing

Accidental release measures

Disposal

Fire fighting information

Cylinders

Protective fire fighting 

equipment

If you are in doubt about the concentration in the atmosphere, it is re-

commended to wear a respirator approved by an accident-prevention 

Authority, of the independent or oxygen type.

Cylinders must be stored in a dry and fresh place, free from any fire 

hazard, far from direct sunlight or other sources of heat, radiators etc. 

Keep a temperature below 50 °C.

Wear overalls, protective gloves and goggles or a mask.

It is important to wear protective clothing and a respirator. Stop the 

source of the leak, if you can do this without danger. Negligible leaks 

can be left evaporating under the sun, providing that the room is well 

ventilated. Considerable leaks: ventilate the room. Reduce the leak with 

sand, earth or other absorbing substances. Make sure that the liquid 

does is not channelled into gutters, sewers or pits where the vapours 

are likely to create a stuffy atmosphere.

The best method is recovery and recycling. If this method is not practi-

cable, dispose according to an approved procedure, that shall ensure 

the absorption and neutralization of acids and toxic agents.

R410A: Not flammable in the atmosphere.

In case of fire, wear an independent respirator and protective clothing.

The cylinders, if exposed to fire, shall be cooled by water jets; othe-

rwise, if heated, they may explode.

General precautions

Do not inhale concentrated vapours. Their concentration in the atmo-

sphere should not exceed the minimum preset values and should be 

maintained below the professional threshold. Being more weighty than 

the air, the vapour concentrates on the bottom, in narrow areas. There-

fore, the exhaust system must work at low level.

VLS-GB.indd 9

17-06-2009 15:56:43

Содержание VLC 1004





















































































Отзывы: