background image

Installation |

11

6.4.1

Assembly the Topvex SoftCooler

Fig. 7 Left hand unit

Make sure that the sealing stripes and faces of sealing in-between the unit half are undamaged.

1. To get access to the upper mounting screws (M8) remove the rectangular covering plate on top of the Topvex

SoftCooler.

Place the Topvex SoftCooler in-between the two air handling unit parts and carefully push them together.

2. When the three parts are completely joined together: Screw the upper and lower mounting screws that joining the

parts.

3. Connect the electrical wiring in the Topvex TR electrical box. Assemble the electrical fast couplings and the transpar-

ent air tubes on each side of the Topvex SoftCooler make sure that they are on the right place by reading the
labelling.

Assemble the plate "A" figure figure 6, heat exchanger, extract- fan and filter.

6.5

Duct connections

When Topvex SoftCooler have been joined together with the two air handling unit parts it is in total 5 duct connections
on top of the unit: Outdoor air, Supply air, Extract air and 2 Exhaust air. Duct connections can be done on two different
ways, with or without a by-pass-function for the exhaust air.

For duct connection without by-pass function on the exhaust air only 4 duct connections are used. The exhaust air duct
are then to be connected to the exhaust air duct connection on the Topvex SoftCooler module. The exhaust air duct
connection on the air handling unit must be locked with the Topvex SoftCooler included locking plate.

For duct connection with "By-pass" function on the exhaust air all 5 duct connections are used. The exhaust air duct are
then to be connected both to the Exhaust air duct connection on the Topvex SoftCooler module and to the one on the
air handling unit.

N.B. Motorized spring return dampers must be mounted on each exhaust air duct connection.

6.6

Condensation and Heat Insulation

Outdoor air duct and discharge ducts must always be well insulated against condensation. Correct insulation installation
on ducts connected to the unit is especially important. All ducts installed in cold rooms/areas must be well insulated.

208767 | A006

Содержание Topvex TR 09 Series

























Отзывы: