background image

2 Warnings

The following admonitions will be presented in the different sections of the document.

Danger

• Make sure that the Mains supply to the unit is disconnected before performing any maintenance or

electrical work!

• All electrical connections must be carried out by an authorized installer and in accordance with

local rules and regulations.

• Operation in the refrigerant circuit and handling refrigerants must be performed by certified personnel.

Warning

• The door handles are only intended to be used during the installation. These must be removed before

the unit is put into operation to ensure the required level of safety for the unit.

• The unit is heavy. Be careful during transport and mounting. Risk of injury through pinching. Use

protective clothing.

• Beware of sharp edges during mounting and maintenance. Make sure that a proper lifting device is

used. Use protective clothing.

• Skin contact with the refrigerant must be avoided. Use protective equipment such as protective

goggles, gloves and suitable clothing’s. Good ventilation must be arranged.

• If freezing injury a doctor must be seen.

• If skin contact the exposed part of the body must be carefully washed.

• If eye contact use eye wash or lukewarm water and wash for 20 minutes, visit a doctor.

• The units electrical connection to the mains supply must be preceded by an all pole circuit breaker

with a minimum 3 mm gap.

Caution

• If the unit is installed in a cold place make sure that all joints are covered with insulation, and tape well

• Duct connections/duct ends should be covered during storage and installation

• Do not connect tumble dryers to the ventilation system

3 Refrigerant Control/Reporting

Topvex SoftCooler TR comes pre-filled with refrigerants and belongs to the group "Piece units containing
more than 3kg refrigerants per circuit". Before commissioning shall always a control report in respect of the
installation be established by a cooling certified person. Leakage control with record keeping shall be done
once per year. The installation of the Topvex SoftCooler TR is only duty to report if the property/enterprise
where the installation occurs, all together after installation, has a total amount of refrigerants of 10 kg or
more ("small Piece units" with refrigerants less than 3 kg, e.g. normal refrigerators/freezers does not
includes). Reporting shall in occurring cases be done to major inspection authority (normally the municipal
environmental office).

Different regulations can be valid in different countries. Check with your local government.

Topvex SoftCooler TR09-15

Installation instructions

208767

2

Systemair Sverige AB

Содержание Topvex SoftCooler TR Series

























Отзывы: