SystemAir SYSHRW 096 Скачать руководство пользователя

Страница: 21 / 46

English

RCL

1 2 3 4

SysHrw

Checking the support bracket :
Ensure that the wall surface is completely flat at the point where you wish to install the RCL control, as it

is important that the support bracket is not twisted on installation, because any bending could lead to the

control not clipping together properly and result in operating difficulties.
Fitting the support bracket :

Present the support bracket to the desired location and align it with a spirit level.

Mark the screw locations.

Make a hole or install appropriate plugs according to the material (wood, concrete, plasterboard etc.).

Screw the support bracket to the wall, preferably with round head screws matching the following

characteristics :

- Minimum length : 15 mm,
- Maximum head diameter : 7 mm,
- Maximum thread diameter : 3.5 mm,
- Head protrusion : 3.5 mm.

15. RCL AND µBMS CONTROL MODULES WIRING

15.1. RCL

The RCL control module must be connected in accordance with the diagram

below.

Use twisted pair telephone wire with a section of between 0.12 and 0.5

mm² for wiring the control modules.

Take care to comply with the terminal connection reference numbers.

Unscrew the lower screw on the RCL control.
Separate the RCL control from its support bracket with the

help of a flat bladed screwdriver

Support

bracket

Lower

screw

LED

Содержание SYSHRW 096















































Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды

SystemAir SYSHRW 096, Руководство по установке и обслуживанию

Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды