background image

Operation |

3

4.1.1

Indicators

General alarm LED shows when any alarm has occurred. Alarm type is not specified.
It is not possible to acknowledge alarms from the SAVE LIGHT control panel. Please check SAVE TOUCH
control panel or contact your local technical service provider.

The filter change LED shows when filters have to be replaced.
Filters cannot be cleaned and must be changed as necessary. This is normally done 2–3 times per year
depending on the air pollution at the installation site.

4.1.2

To select airflow level

LEDs show current airflow level (figure 3, pos. 3).

• Press

button to increase the airflow.

• Press

button to decrease the airflow.

Off

Low

(Minimum)

Normal

High

Refresh

(Maximum)

Auto — flashing

slowly

The fan can be
set to

Off

by

activating

Manual Fan
Stop

function in

Service

menu.

Fan speed – 25%

Fan speed – 45%

Fan speed – 70%

Sets speed of
both supply and
extract air fans
to

Maximum

levels to replace
indoor air with a
fresh air in a
short period of
time.
The unit returns
to previously
active mode
after 1 hour
when in the

Refresh

mode.

Automatic
airflow control.
Available only
when

Week

Schedule

,

Demand
Control

functions are
active or

Fan

Control

setting

is set to

External

.

Note:

Minimum

and

Maximum

airflow can only be activated by a signal from an external source.

Auto

mode or

Manual Fan Stop

function can be enabled using the SAVE TOUCH control panel or a

mobile application.

• It is

not

recommended to set fan to

Off

in standard households. If manual fan stop is activated, the unit

should be provided with dampers in exhaust and fresh air ducts to avoid cold draught and risk of
condensation when the unit has been stopped.

4.1.3

To cancel sleep mode

Press any button to cancel the sleep mode. SAVE LIGHT returns to the sleep mode after 3 minutes of inactivity.

All control panel lights are off during sleep mode. The sleep mode is active from 9:00 PM to 7:00 AM (based on time of
the air handling unit).

4.1.4

To change control panel address (if more than one control panel is used)

If more than one SAVE LIGHT control panel is used, the address of other control panels must be changed.

Each control panel must have it’s own unique address number. No control panel should have the same address value to
function properly.

1. Push and hold

button for 10 seconds to see a current control panel address value.

254493 | v01

Содержание 488831























Отзывы: