SYRUNS SY6000-Z Series Скачать руководство пользователя страница 2

Страница: 2 / 24

User Manual of SY6000-Z series Preface

REFACE

Thanks for choosing SY6000-Z series moulding injection

energy saving cabinet.

SY6000-Z series cabinet is high quality moulding injection

energy saving drive which is designed according to

IEC618000/IEC610000. The cabinet owns protection functions of

phase-loss, over voltage, under voltage, over current, etc.

SY6000-Z series cabinet is suitable for kinds of moulding

injection machine with hydraulic control proportional pump. It

controls output power of motor according to pressure signal and

flow signal of moulding injection machine to reach the objective

of energy saving. The energy saving rate may get 25%~65%.

SY6000-Z series cabinet can work for pump motors which

power ratings are from 11KW~55KW. It also can apply for one

moulding injection machine with multiple pump motors.

Before using SY6000-Z series cabinet, in order to keep

people in safe and acquire better energy-saving effect, please read

the manual thoroughly. If you meet with tough problems when

using, please contact us in time.

Please retain this manual and you will use it if necessary in

future.

Содержание SY6000-Z Series

























Результаты поиска

Содержание SY6000-Z Series

Отзывы:

Похожие инструкции для SY6000-Z Series

Бренды по названию

Популярные бренды

SYRUNS SY6000-Z Series, Руководство пользователя

Результаты поиска

Содержание SY6000-Z Series

Отзывы:

Похожие инструкции для SY6000-Z Series

Бренды по названию

Популярные бренды