Synthes Anspach Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 46

Synthes Anspach Скачать руководство пользователя страница 20

Console Indicators

Code

Description Audible Signal* Corrective Action

E1, E8

System Fault None Turn Power switch to off, and then back on. If fault does not clear,

return console and handpiece to Synthes Anspach for service.

E2

Handpiece Lock 10 slow beeps Rotate the knurled knob on handpiece clockwise to ensure the
Engaged handpiece is not locked.

E3

Handpiece Stall 10 fast beeps Remove pressure from foot control (or hand control),
Warning remove cutter from stalled location and restart handpiece.

E4, E5

Fault in Handpiece None Return console and handpiece to Synthes Anspach for service

E6, E7

Handpiece overheat   5 second beep   Reduce or remove load from handpiece to allow handpiece to
warning, impending      cool. If load is not reduced sufficiently, handpiece will shut down
handpiece shutdown     30 seconds after tone is heard and/or code is displayed.

E9

Handpiece type None Disconnect connector and reconnect to console. If fault does not
not recognized clear, return handpiece and console to Synthes Anspach for service.

None

Handpiece set 3 beeps
to reverse

*

Note:

Consoles with Software Version 3.0 and higher do not generate an Audible Signal for Codes E1– E9.

Anspach Electric Systems

Instructions for Use

Synthes

19

0x6.001.507_AD 13.06.14 11:12 Seite 19

«
...
18
19
20
21
22
...
»

Содержание Anspach















































Отзывы:

Нет отзывов