Synrad Novanta 48 Series Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 89

Synrad Novanta 48 Series Скачать руководство пользователя страница 78

CLEANING GUIDELINES

PAGE

|

78

the Dew Point temperature in °F (or °C). The chiller’s temperature setpoint must be set above the dew

point temperature.
For example, if the air temperature is 85 °F (29 °C) and the relative humidity is 60%, then the dew point

temperature is 70 °F (21 °C). Adjust the chiller’s temperature setpoint to 72 °F (22 °C) to prevent

condensation from forming inside the laser.
Refer to the dew point temperature table within the prior section for a range of air temperature and relative

humidity values. Remember that the laser’s coolant temperature must be set above the dew point

temperatures shown in the chart, but should not exceed the environmental specifications located in the

Series 48 General Specifications within the Technical References section of this manual.
Debris or contaminants on the laser’s output coupler or external beam delivery components may affect

laser processing and lead to damage or failure of the optics and/or the laser. Carefully follow the steps

below to inspect and clean the optical components in the beam path. Before beginning the cleaning

process, read this entire section thoroughly to ensure that all cleaning materials are available and that each

step is completely understood.

Important Note: Exercise great care when handling infrared optics; they are much more fragile

than common glass materials. Optical surfaces and coatings are easily damaged by rough handling

and improper cleaning methods.

Cleaning guidelines

•

Wear latex gloves or finger cots (powder-free) to prevent contamination of optical surfaces by dirt

and skin oils.

•

Never handle optics with tools; always use gloved hands or fingers.

•

Hold optics by the outer edge; never touch the coated surface.

•

Always place optics lens on a tissue or suitable equivalent material for protection; never place

optics on hard or rough surfaces.

•

It may be necessary to use a cotton ball or fluffed cotton swab instead of a lens wipe to uniformly

clean the entire surface of small-diameter mounted optics.

•

Before using any cleaning agents, read Material Safety Data Sheets (MSDS) and observe all

necessary safety precautions.

Required cleaning materials

The table below lists the type and grade of materials required to properly clean optical surfaces.

Table 5-1 Required cleaning materials.

«
...
76
77
78
79
80
...
»

Содержание Novanta 48 Series


























































































Отзывы:

Нет отзывов