SynQor MPC-1500 Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 48

SynQor MPC-1500 Series Скачать руководство пользователя страница 4

Section I

Warnings

006-0006452 MPC-1500 Operator Guide

Rev P

4 of 48

03/03/2021 www.synqor.com

Section I

Warnings

Hazardous Voltages

The INPUT AND OUTPUT POWER connectors and cables of the SynQor MPC may have

voltages that are unsafe. INJURY OR DEATH ON CONTACT may result. Appropriate safety

precautions should be taken. All connections should be made in accordance with LOCAL

ELECTRICAL CODES.
• The MPC CHASSIS should be connected to earth or system ground with Ground Stud on the

rear panel, see mechanical diagrams.

• For the AC INPUT cable and connector:

▪ Do not assume that a hazardous voltage is not present at the terminals of the AC input

connector, even if the MPC appears to be off.

▪  Do not make contact with the terminals of the AC input connector.
▪  Always connect the cable to the MPC before it is connected to the source of AC power.
▪  Always disconnect the AC input cable from the source of AC power before disconnecting it

from the MPC.

▪ If the AC input cable is connected to the source of AC power and not connected to the MPC,

do not contact the exposed terminals of the AC input cable.

▪ Do not assume that the source of AC power is not present.
▪ Connections between the AC input cable and the source of AC power should not be

accessible.

• For the AC OUTPUT cable and connector:

▪ Do not assume that a hazardous voltage is not present at the terminals of the AC output

connector, even if the MPC appears to be off.

▪  Do not make contact with the terminals of the AC output connector.
▪  Connect the AC output cable to the MPC before the MPC is turned on.
▪  If connection of the load to the AC output cable has exposed conductors, make this connection

before connecting the AC output cable to the MPC.

▪ Connections between the AC output cable and the load should not be accessible.

• For the DC INPUT cable and connector (if present):

▪ The rated DC input voltage of the MPC is below the level considered hazardous.
▪ The DC input terminals of the MPC are isolated from the AC input and AC outputs with

reinforced safety insulation.

▪ However, never assume the terminals of the DC input connector or the wires of the DC input

cable are safe to contact, even if the MPC or DC input source appears to be off.

«
...
2
3
4
5
6
...
»

Содержание MPC-1500 Series

















































Отзывы:

Нет отзывов