SynQor Headquarters UPS-1500 Series Скачать руководство пользователя страница 51

Страница: 51 / 60

Section VI

Control Interface Details

006-0006205

UPS-1500 Series

Rev ZC

51 of 60

05/28/2019

www.synqor.com

Readback information that is available:

For a detailed description of the terminal interface see the SynQor website at:

http://www.SynQor.com/UPS/documents/UPS_User_Commands.pdf

Ethernet Interface

The Ethernet interface provides a web page based user interface for monitoring and control

of the UPS. The user can configure email alerts for UPS alarm conditions. The interface also

exposes an SNMP interface compliant to RFC-1628.

The Ethernet interface supports 10BASE-T and 100BASE-T standards. It utilizes a standard RJ-45

connector, also allowing a metallic sealable circular military outer housing. The interface supports

auto-negotiation, polarity correction, and Auto-MDIX (detection and use of straight through or

cross-over cables).

IP address assignment can be done via DHCP or user entry of a static address. The interface also

supports a direct connection between the UPS and a host computer by including a DHCP server

internal to the UPS.

For a detailed description of the Ethernet port and SNMP implementation see the SynQor website

at:

http://www.synqor.com/ups/documents/UPS_Ethernet_SNMP_UG.pdf

• AC Input Voltage

• AC Input Current

• AC Input Frequency

• DC Input Voltage

• AC Output Voltage

• AC Output Current

• AC Output Power

• AC Output Frequency

• DC OUTPUT Power

• Total Output Power

• Battery Voltage

• Battery State of Charge

• Battery Predicted Run Time

• Number of Battery Cycles

• External Switch Input Status

• Fan RPM

• Internal Temperatures

Parameters that are controllable through the interface:

• Output enable / disable

• Fan diagnostics

• Alarm enable / disable

Содержание UPS-1500 Series





























































Результаты поиска

Содержание UPS-1500 Series

Отзывы:

Похожие инструкции для UPS-1500 Series

Бренды по названию

Популярные бренды

SynQor Headquarters UPS-1500 Series, Руководство оператора

Результаты поиска

Содержание UPS-1500 Series

Отзывы:

Похожие инструкции для UPS-1500 Series

Бренды по названию

Популярные бренды