Synopsys DesignWare ARC AXC003 Скачать руководство пользователя страница 137

Страница: 137 / 145

137

Synopsys, Inc.

Version 6323-018

May 2017

Appendix C

This appendix describes all features of the core configurations available in the AXC003
Processor FPGA.

C.1

Detailed Core Configurations

Configuration
Option

Description

HS36

HS38x2

Cluster

Cluster

Cluster component

cluster_id

CLUSTER_ID auxiliary register

pipeline_ibps

Place pipeline registers on internal busses
within the cluster to assist timing closure at
high frequency

false

CPUisle

arc_num

Processor number as read back in the
ARCNUM

instances

The number of instantiations of this core

ARCv2HS

halt_on_reset

The core is halted initially on reset

true

byte_order

The endianness of the core

little

atomic_option

Enables the LLOCK/SCOND instructions

true

div_rem_option

Adds non-blocking multi-cycle implementation
of integer divide/remainder functions

radix4_
enhanced

mpy_option

The multiplier ISA option

plus_qmacw plus_qmac

stack_checking

A mechanism for checking stack accesses

true

ll64_option

Support for load and store instructions that
transfer register pairs to/from memory

true

intvbase_preset

The upper 22 bits of the interrupt vector base
configuration register

Содержание DesignWare ARC AXC003


















































































































































Результаты поиска

Содержание DesignWare ARC AXC003

Отзывы:

Synopsys DesignWare ARC AXC003, Руководство пользователя, Страница: 137 / 145

Результаты поиска

Содержание DesignWare ARC AXC003

Отзывы: