manualshive.com logo in svg

Symmetricom TimeProvider 500 series, Справочное руководство

Поделиться
Скачать
Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 47

Issue 2: Sep 99

TMSL 097-44018-26

Page 47

COMMAND CODE: ED-SSM-MSG

PURPOSE

EDIT SYNCHRONIZATION STATUS MESSAGING

This command assigns a quality level to the output signals of a TOTA-M, EA10-M, EA20-M, GTI-17, or
GTI-18 card. On TOTA-M, EA10-M, and EA20-M cards, the assigned message will be sent only if the
TOTA-M, EA10-M, or EA20-MA card loses communicatins with the MIS card for longer than 2 seconds.
On GTI-17 and GTI-18 cards, the assigned message will be sent only if the output signal from the GTI-
17 or GTI-18 card is not traceable to PRS/PRC and the card signal is still active.

INPUT FORMAT

ED-SSM-MSG:[<tid>]:<aid>:<ctag>::<ssmmsg>;

The parameter values in the table below are as follows:

a

= 1–2

b

= 1–12

parameter

value

for card

meaning

aid

GTI-a

GTI-17, GTI-18

Specified GTI card

TO-b

TOTA-M, EA10-M,
EA20-M

Specified output card

ssmmsg

QL-DNU

EA10-M, EA20-M, 
GTI-18

Do not use for synchronization

QL-DUS

GTI-17, TOTA-M

Do not use for synchronization

QL-HOLDOVER

EA10-M, EA20-M, 
GTI-17, GTI-18, 
TOTA-M

Output quality level based on quality level of shelf clocks

QL-PRC

EA10-M, EA20-M, 
GTI-18

Signal is traceable to a primary reference clock

QL-PRS

GTI-17, TOTA-M

Signal is traceable to a primary reference source

QL-RES

TOTA-M, GTI-17

Signal is traceable to a user-definded level

QL-SEC

EA10-M, EA20-M, 
GTI-18

Signal is traceable to SDH equipment clock

QL-SMC

GTI-17, TOTA-M

Signal is traceable to SONET minimum clock

QL-SSUL

EA10-M, EA20-M, 
GTI-18

Signal is traceable to synchronization supply unit local

QL-SSUT

EA10-M, EA20-M, 
GTI-18

Signal is traceable to synchronization supply unit transit

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды