Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 165

background image

Issue 2: Sep 99

TMSL 097-44018-26

Page 29

COMMAND CODE: ED-COM

PURPOSE

EDIT COMMUNICATION

This command changes communication parameters. Communication port parameters which cannot be
changed are: character bits = 8, parity = none, and start bits = 1. When changing communication param-
eters, the associated hardware (modem, pad, or terminal) must be connected. After changing a parame-
ter with this command, wait at least 10 seconds before entering another command.

INPUT FORMAT

ED-COM:[<tid>]:<aid>:<ctag>::[<baud>],[<monmsg>],[<keepalive>]

,[<comtype>],[<endoftext>],[<echo>],[<compri>]
,[<hwcontrol>],[<swcontrol>][,[<dur>],[<dn>]];

Notes:

1.

Any parameter left blank causes no change to that parameter.

2.

Before changing the <comtype>, the cable on the communication port specified in the <aid> must be
disconnected. If the cable is not disconnected and an attempt is made to change only the <comtype>
parameter, an SROF error message will be returned. If the cable is not disconnected and an attempt
is made to change <comtype> plus other parameters, a completed response will be returned to show
that all parameters other than <comtype> were changed.

parameter

value

meaning

aid

COM-1

communication port 1 (backplane D connector)

COM-2

communication port 2 (backplane D connector or front panel RJ connector)

COM-3

communication port 3 (backplane D connector)

baud

1200

1200 baud

9600

9600 baud

Note: the baud parameter must be set to null when the aid is COM-2

monmsg

ALW

allows this port to view communication messages associated with other communica-
tion ports in real-time

INH

inhibits this port from viewing communication messages associated with other commu-
nication ports in real-time

keepalive

ALW

allows a port to autonomously output a COMPLD message every 15 to 20 minutes

INH

inhibits a port from autonomously outputting a COMPLD message every 15 to 20
minutes

«
...
27
28
29
30
31
...
»

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TimeProvider 500 series

Бренд: PCsensor Страницы: 3

Бренд: Velleman Страницы: 2

Бренд: Rotronic Страницы: 2

Electrocorder EC-1A

Бренд: Acksen Страницы: 3

Бренд: Pyle Страницы: 5

Бренд: HENGKO Страницы: 78

Бренд: Abtus Страницы: 22

Бренд: Hantek Страницы: 36

Бренд: JERICHO Страницы: 16

Бренд: Velleman Страницы: 44

Бренд: AEM Страницы: 22

Бренд: Triplett Страницы: 7

Бренд: Triplett Страницы: 14

Бренд: SOMMER Страницы: 100

Бренд: Stack Страницы: 2

Бренд: Sunways Страницы: 16

Tinytag Connect

Бренд: Intab Страницы: 72

Бренд: Dewetron Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды